WetWorx LLC  //  Panama City Beach, Florida Research  ·  Development  ·  Rapid Prototyping

Product line

Target Systems

A printed-frame quadrotor target built to be struck and rebuilt. The electronics are retained. The frame is the consumable.

WETWORX target drone, FPV configuration: printed quadrotor frame, four motors, strapped lithium pack, nose-mounted camera and whip antenna.
FIG 01Target airframe, FPV configuration. Printed frame, connectorized electronics stack.

Two configurations

Line of sight. No camera and no video transmitter. Flown by an operator watching the aircraft, for crew drill and gunnery where the training event is the engagement rather than the flight. Fewer components in the air means less value lost on a hit.

FPV. Camera and video transmitter fitted, flown from onboard video. This is the presentation that matches what crews are being trained to defeat, including approach profiles a line-of-sight operator cannot fly.

Both configurations share one airframe, one frame file and one electronics architecture, so a unit stocks one set of spares.

The team's UAS research and development has produced and flight-validated airframes spanning micro-class FPV through 10-inch quadrotor and fixed-wing configurations.

Airframe — specification
ClassGroup 1
ConfigurationQuadrotor, printed frame
Airframe size7-inch propeller class
All-up weightTBD
Maximum speedTBD
EnduranceTBD
Battery6S 1300 mAh
Frame materialCONFIRM
Frame print timeTBD on CORE One L
Control linkTBD
Failsafe on link lossCONFIRM
Build time from kitTBD
Frame swap timeTBD

Performance figures are released against a stated configuration once first-article testing is complete. Nothing is published here that cannot be demonstrated on request.

Serviceable core

The stack survives.
The frame does not.

Every interface on the aircraft is connectorized, so the flight electronics come out of a struck airframe as one assembly and go into a fresh frame without a soldering iron.

  • Flight electronics are treated as a line replaceable unit, not a repair item
  • Motor, power, camera and video interfaces are connectorized to one documented standard held under configuration control
  • Spare frames ship with hardware pre-installed — standoffs, motor screws and camera cradle
  • One-for-one frame swap with a screwdriver, no soldering
  • Motors are supplied with pigtail and connector attached, so a motor change is a swap
FRAME / CONSUMABLESTACK / RETAINED STRUCKREBUILT

Consumables and resupply

Frame refresh kit

Assembled frame with hardware installed. Consumed on every rebuild, whatever else survived the engagement.

Impact kit

Propellers and motors supplied with pigtails and connectors attached for a direct swap.

Battery

Cycled out on hours and handling regardless of whether the aircraft is ever struck.

Stack refresh

Full electronics replacement, for the cases where the flight stack does not survive.

Ordering — part numbers SCHEME PROVISIONAL
Part numberItemNotes
WWDT-T7-LOS-ATarget airframe, line of sightComplete aircraft, no camera or VTX
WWDT-T7-FPV-ATarget airframe, FPVComplete aircraft, camera and VTX fitted
WWDT-T7-FRM-AFrame refresh kitAssembled frame, hardware installed
WWDT-T7-IMP-AImpact kitPropellers and pigtailed motors
WWDT-T7-BAT-ABattery6S 1300 mAh
WWDT-T7-STK-AStack refreshFull electronics replacement
…-SScreened configurationSame item built to a component-screened BOM. Ordered and quoted separately.

The trailing letter is the configuration revision. A component substitution does not ride into an existing part number; it becomes a new revision with its own documentation. Pricing is quoted, not published — request a quote.

In development

Stated as roadmap,
not as capability

  • Onboard flight termination. In design. Required for range use where it is specified.
  • Range system compatibility. Interface requirements under review against customer range architecture.
  • Programmed flight profiles. Repeatable presentations so every student on the line sees the same event. Ground control is a partner capability, not a WetWorx product.
  • Screened bills of material. Component-screened configurations are assigned distinct part numbers and quoted separately. See Security & Compliance.

Items in this list are in development and are not offered as delivered capability.

Next step

Request a quote

Tell us the requirement, the quantity, and the date. We quote against a stated configuration and can send a capability brief.